Student-Contributed Wiki

1. Hoover Power Scrub Elite Fh50258
2. Hoover Power Scrub Elite Pet User Manual Free
3. Hoover Power Scrub Elite Problems
4. Hoover Power Scrub Elite Pet User Manual Instructions

View online or download Hoover ELITE FH50251 User Manual. Hoover Manuals; Vacuum Cleaner; ELITE FH50251; Hoover ELITE FH50251 Manuals Manuals and User Guides for Hoover ELITE FH50251. We have 1 Hoover ELITE FH50251 manual. Getting Started With Your Power Scrub Elite 12. Using Your Power Scrub Elite 16. Hoover FH50258 instruction manual and user guide Professional Series Power Scrub Elite Pet Plus Upright Carpet Cleaner FH4345.

An awesome team of students from our education program made this wiki.

Troubleshooting symptoms and solutions for the Hoover Power Scrub FH50150 carpet cleaner.

Low Suction

The Power Scrub will not pick up water even though the power is on.

If the water tank is full, you’ll hear a change in pitch and the yellow disk inside the tank will shoot to the top which means the cleaner will not pick up anymore water. You will have to remove the tank and dump out the water before continuing use.

If the cleaner is still not picking up water, you may have to rinse out the various parts with water before continuing. Try to rinse out the water tank, including the foam filter, and also rinse out the nozzle as it may have clogs in it. Make sure the circular hose tool connection door on the nozzle is closed as well.

Hose Nozzle not Spraying

The hose nozzle is not spraying even though you are holding down the trigger.

If the cleaner stops spraying mid clean, or you can't remember the last time you filled it up you may have an empty water tank or detergent container. Turn off the cleaner, Remove and fill up both the clean water tank and the detergent container. See if it fixed your spraying issue.

If the cleaner is still not spraying despite the water and detergent tanks being full, there may be a bubble of air stuck in the pump or the hose. To fix this, you need to turn the cleaner on and lower the hose down to the floor. Next, prime the pump by holding down the trigger for up to 1 minute. If this doesn't help you should call (1-800-944-9200) for service to your device, it probably needs a replacement pump.

Brushes Won't Rotate

The brushes are not rotating during the carpet washing process.

Hoover Power Scrub Elite Fh50258

If your brushes are not rotating try removing the brushes and and check to see if they are rotating smoothly and freely when outside of the washer. If they are then most likely the air powered brush motor has ceased rotation due to rust inside. To fix this, you must remove the top of the washer by unscrewing the indicator screws on the top of the washer and pulling the flap on the side. Next, unscrew the plastic covering to reveal the motor. Clean the rust from the center screws and gears in the center of the motor until it spins freely.

If you have tried cleaning the rusted gears and the brush still will not rotate. Order a new motor online to replace the rusted motor. Replacement can be done by following the same steps as above.

Clean Water Won’t Dispense

Clean water won’t spray out of the hose nozzle.

Make sure the tank is securely locked in place. If this is done correctly, you should hear a noticeable click when the tank is securely locked in to its place.

If you don’t remember the last time you filled up the clean water tank or solution container, one or both of these may be empty. Remove the tank and container to check to see if they are full. If they are empty, fill them following the instructions for the type of surface you wish to clean.

Washer Cannot Pick Up Dirty Water

The carpet washer can no longer pick up dirty water and most likely the motor sound is at a higher tone.

First and foremost, turn the washer off. Then, proceed to empty the dirty water tank by releasing the latch which is located at the bottom portion of the tank. Open the quick spout port cap over a drain and proceed to dump all water into the drain. When emptying, rinse all debris and flush out all the water. Place the tank back within the washer and reattach the recovery tank lid latch.

Turn the power off and pull the power cord out of the socket. Then, remove the water/solution tank. It may need to be rinsed out and refilled in this case. Continue by replacing the turning caps back in and placing the tank back in place.

Leaky Tank

Hoover Power Scrub Elite Pet User Manual Free

There is a constant drip of water on the floor and there is an excess of water when the tank is taken out.

Start by making sure the power is off and it isn’t plugged in. Take off the tank with the button over the filler caps. Then, proceed to put back the tank in place by setting the bottom edge down and then pivot it back and have it be properly straight and aligned when snapping into place.

Hoover Power Scrub Elite Problems

Hoover Power Scrub Elite Pet User Manual Instructions

Have the device be off and remove the dirty water tank straight out using the bottom hatch and handle. Follow up with placing the tank back on, making sure that it is aligned and properly sealed. Proceed by closing the hatch in the front to stop further movement.