1. Bunn Hot Water Dispenser User Manual Scalding Instructions
2. Bunn Hot Water Dispenser User Manual Scalding System
3. Bunn Hot Water Dispenser User Manual Scalding Parts
4. Bunn

HW2

View and Download Bunn H5M operating & service manual online. Bunn OPERATING & SERVICE MANUAL Hot Water Dispenser H5M. H5M Water Dispenser pdf manual download. Bunn Hot Water Dispensers and Water Dispenser Parts. Our precise temperature water dispensers are a reliable, dependable and economical source for a consistent supply of piping hot water for tea, soups and instant hot beverages. Our Bunn hot water dispensers maintain a water temperature near boiling, which ensures that you have a ready supply.

HW2A

HOT WATER DISPENSERS

INSTALLATION & OPERATING INSTRUCTIONS

INTRODUCTION

This equipment heats and dispenses water on demand for beverages and cooking purposes.

WARRANTY

Bunn-O-Matic Corp. (“Bunn”) warrants the equipment manufactured by it to be commercially free from defects in material and workmanship existing at the time of manufacture and appearing within one year from the date of installation. In addition:

1.) Bunn warrants electronic circuit and/or control boards to be commercially free from defects in material and workmanship for two years from the date of installation.

2.) Bunn warrants the compressor on refrigeration equipment to be commercially free from defects in material and workmanship for two years from the date of installation.

3.) Bunn warrants that the grinding burrs on coffee grinding equipment will grind coffee to meet original factory screen sieve analysis for three years from date of installation or for 30,000 pounds of coffee, whichever comes first.

This warranty does not apply to any equipment, component or part that was not manufactured by Bunn or that, in Bunn’s judgement, has been affected by misuse, neglect, alteration, improper installation or operation, improper maintenance or repair, damage or casualty.

THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of Bunn are not authorized to make modifications to this warranty or to make additional warranties that are binding on Bunn. Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and should not be relied upon.

The Buyer shall give Bunn prompt notice of any claim to be made under this warranty by telephone at (217) 529-6601 or by writing to Post Office Box 3227, Springfield, Illinois, 62708-3227. If requested by Bunn, the Buyer shall ship the defective equipment prepaid to an authorized Bunn service location. If Bunn determines, in its sole discretion, that the equipment does not conform to the warranty, Bunn shall repair the equipment with no charge for parts during the warranty period and no charge for labor by a Bunn Authorized Service Representative during the warranty period. If Bunn determines that repair is not feasible, Bunn shall, at its sole option, replace the equipment or refund the purchase price for the equipment.

THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AS SPECIFIED HEREIN, TO REPAIR OR, AT BUNN’S SOLE OPTION, REPLACEMENT OR REFUND.

In no event shall Bunn be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other special, incidental or consequential damages.

BUNN-O-MATIC CORPORATION

POST OFFICE BOX 3227

SPRINGFIELD, ILLINOIS 62708-3227

PHONE: (217) 529-6601 FAX: (217) 529-6644

USER NOTICES

The notices on this dispenser should be kept in good condition. Replace unreadable or damaged labels.

00657.0000

00831.0000

ELECTRICAL REQUIREMENTS

CAUTION - The dispenser must be unplugged until specified in Initial Set-Up.

The Model HW2 has an attached cordset and requires 2-wire, grounded service rated 120V ac, 15 amp, single phase, 60 Hz. The Model Hw2A requires 2-wire grounded service rated 240V ac, 8 amp, single phase, 50 Hz.

PLUMBING REQUIREMENTS

This dispenser must be connected to a cold water system with operating pressure between 20 and 90 psi (138 and 620 kPa) from a 1/2' or larger supply line. A shut-off valve should be installed in the line before the dispenser. Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi (345 kPa). The water inlet fitting is 1/4' flare.

NOTE - Bunn-O-Matic recommends 1/4' copper tubing for installations of less than 25 feet and 3/8' for more than 25 feet from the 1/2' water supply line. A tight coil of copper tubing in the water line will facilitate moving the dispenser to clean the countertop. Bunn-O-Matic does not recommend the use of a saddle valve to install the dispenser. The size and shape of the hole made in the supply line by this type of device may restrict water flow.

This equipment must be installed to comply with the Basic Plumbing Code of the Building Oficials and Code Administrators Internatiopnal, Inc. (BOCA)

and the Food Service and Drug Administration (FDA).

Plumbing Hook-Up

1.Flush the water line and securely attach it to the bulkhead fitting on the rear of the machine.

2.Turn-on the water supply.

INITIAL SET-UP

CAUTION - The dispenser must be disconnected from the power source throughout the initial set-up, except when specified in the instructions.

1.Remove the center rear panel and rotate the control thermostat knob fully counterclockwise to the “OFF” position and replace the panel.

2.Plug-in the dispenser.

3.Water will automatically flow into the tank to the proper level and shut-off.

4.Unplug the dispenser, remove the center rear panel and rotate the control thermostat knob fully clockwise to the “ON” position, and replace the panel.

5.Plug-in the dispenser and wait approximately twenty minutes for the water in the tank to heat. The dispenser is ready for use.

CLEANING

The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all surfaces on Bunn-O-Matic equipment.

WIRING DIAGRAMS

Page 4: 120 volts a c 2 wire single phase, 240 volts a c 2 wire single phase

4

1700W

TANK HEATER

1

4

LIMIT

THERMOSTAT

BLK

10261.0000E 5/98 © 1987 BUNN-O-MATIC CORPORATION

SCHEMATIC WIRING DIAGRAM HW2

L1

N

BLK

BLK

WHI

SOL

GREEN

3

2

BLU/BLK

WHI

WHI

BLK

BLK

LIQUID

LEVEL

BOARD

SAFETY SW

(PROBE)

P

N
K

WHI

WHI

WHI

WHI

KEEP WARM HEATER

40W

SW. &

THERMOSTAT

KEEP WARM HEATER

40W

120 VOLTS A C

2 WIRE

SINGLE PHASE

RED

RED

1700W

TANK HEATER

1

4

LIMIT

THERMOSTAT

BLK

10261.0001E 5/98 © 1998 BUNN-O-MATIC CORPORATION

SCHEMATIC WIRING DIAGRAM HW2A

L1

L2

BLK

BLK

RED

SOL

GRN/YEL

3

2

BLU/BLK

RED

BLK

BLK

LIQUID

LEVEL

BOARD

SAFETY SW

(PROBE)

P

N
K

WHI

Bunn Hot Water Dispenser User Manual Scalding Instructions

WHI

KEEP WARM HEATER

34W

SW. &

THERMOSTAT

KEEP WARM HEATER

34W

240 VOLTS A C

2 WIRE

SINGLE PHASE

RED

RED

RED

RED

RED

Bunn Hot Water Dispenser User Manual Scalding System

WIRING DIAGRAMS

Bunn Hot Water Dispenser User Manual Scalding Parts

10052 061598

Bunn